-
DS 390101-AEM Electronics Universal Trim Pots 30-2056Vendor: My StoreAEM Electronics Universal Trim Pots A tweak here and a trim there—AEM universal trim pots will shape your engine's efficiency for performance. These 12-position trim pots can be used with virtually any engine management system to adjust a number of trims … from fuel...
- Dhs. 220.00
- Dhs. 220.00
- Unit price
- per
-
DS 390115-AEM Electronics Water/Methanol Injection Replacement Components 30-3314Vendor: My StoreAEM Electronics Water/Methanol Injection Replacement Components AEM Electronics offers a full line of replacement components for your water/methanol injection system. These components are direct replacements for the original pieces, so you can be assured of the highest quality and a correct fit. Tubing, Water...
- Dhs. 80.00
- Dhs. 80.00
- Unit price
- per
-
DS 390054-AEM Electronics Water Injection System Kit 30-3325Vendor: My StoreAEM Electronics Water Injection System Kit 30-3325 V2 Water/Methanol Injection 1.15 Gallon Tank Kit With Conductive Fluid Level Sensor . 8.8 x 12.2 x 12.2 inches 2.71 pounds
- Dhs. 700.00
- Dhs. 700.00
- Unit price
- per
-
DS 390114-AEM Electronics 30-2224 - AEM Electronics 8-Channel K-Type EGT CAN ModulesVendor: My StoreAEM Electronics 8-Channel K-Type EGT CAN Modules The AEM Electronics 8-Channel K-Type EGT CAN module uses an integrated cold junction sensor to ensure lab-grade temperature readings across all eight channels. It has the ability to read better than one percent full scale, even at...
- Dhs. 1,490.00
- Dhs. 1,490.00
- Unit price
- per
-
DS 390052-AEM 30-2130-50 50 PSIA or 3.5 Bar MAP Sensor KitVendor: My StoreAEM 30-2130-50 50 PSIA or 3.5 Bar MAP Sensor Kit High-quality sealed sensor housings Mating connector and 12inch leads included (sensors) when applicable Accurate and affordable AEM offers several sensor and Plug & Pin connector kits for vehicles that require additional outputs and/or upgraded...
- Dhs. 350.00
- Dhs. 350.00
- Unit price
- per
-
DS 390074-AEM Electronics 30-3350 - AEM Electronics Water/Methanol Injection KitsVendor: My StoreWater/Methanol for All Boost Levels of Forced Induction Gas Race EnginesAEM offers two different water/methanol controller designs for gas vehicles: One is boost dependent for forced induction vehicles up to 35 PSI of boost (kit PN 30-3300). The Boost Dependent controller has an on-board...
- Dhs. 1,450.00
- Dhs. 1,450.00
- Unit price
- per
-
DS 01262-AEM 30-3300 Water Methanol Injection Kit 1.15 Gallon Tank V3 with MAP SensorVendor: My StoreTHE AEM WATER/METHANOL INJECTION SYSTEM ADVANTAGEWater/methanol injection for forced induction (turbocharged or supercharged) gas-powered race engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation. This allows racers to reliably increase boost and advance ignition timing—without using high-octane...
- Dhs. 1,595.00
Dhs. 1,800.00- Dhs. 1,595.00
- Unit price
- per
Popular Products
Vendor:
My Store
ACL Race Series engine bearings provide the dependability it takes to hold up under higher RPM conditions. The unique combination of design, metallurgy and engineering come together to deliver what drivers expect from high performance parts. Main Bearing Set Bearing sizes listed: STD APPLICATION 1:...
- Dhs. 450.00
- Dhs. 450.00
- Unit price
- / per
Vendor:
My Store
High performance driving demands that you use the best parts. So rely on ACL's Race Series bearings to perform to the exacting race standards you expect.SUITS: Toyota engine 1FZ-FE 4.5L DOHC ACL Race Series engine bearings provide the dependability it takes to hold up...
- Dhs. 450.00
- Dhs. 450.00
- Unit price
- / per
Sidebar
Categories
Recently Viewed Products
- Choosing a selection results in a full page refresh.